Network-technologies SM-nXm-15V-LCD Manual de usuario

MAN067 Rev Date 4/1/2013 SM-nXm-15V-LCD Video Matrix Switch Installation and Operation Manual

NTI VEEMUX VIDEO MATRIX SWITCH 6 Power Up 1. Plug the VEEMUX into an AC power outlet. 2. Power ON the VEEMUX. 3. Power ON the video sources and

NTI VEEMUX VIDEO MATRIX SWITCH 7 CONTROL OPTIONS The VEEMUX video matrix switch has four methods of control: • Front Panel LCD with Keypad • Dire

NTI VEEMUX VIDEO MATRIX SWITCH 8 Scan Mode Scan Mode causes an output port to automatically switch from one input port to the next consecutive input

NTI VEEMUX VIDEO MATRIX SWITCH 9 On the DB-9 female connector, pins 4 (DSR) and 6 (DTR) are shorted and pins 7 (CTS) and 8 (RTS) are shorted. Theref

NTI VEEMUX VIDEO MATRIX SWITCH 10 Command Definitions (Continued) Command String Good Response Description RS SW *<CR> Internal Reset RV SW,

NTI VEEMUX VIDEO MATRIX SWITCH 11 NTI Switch Control Program For Windows 9X, NT, 2000, XP, Vista And 7 The NTI Switch Control Program is an easy and

NTI VEEMUX VIDEO MATRIX SWITCH 12 Ethernet Operations Key Selection Description 1) Set Unit IP Address - enter the desired IP address in xxx.x

NTI VEEMUX VIDEO MATRIX SWITCH 13 ETHERNET CONTROL Telnet Interface-Port 2000 The Telnet Interface enables the user to control the switch using t

NTI VEEMUX VIDEO MATRIX SWITCH 14 S- nn,mm *<CR> Remove input mm from Scan List of output nn Sx nn *<CR>oooxoxxxooooxxx<CR> Dis

NTI VEEMUX VIDEO MATRIX SWITCH 15Command Detail RU-Read Unit Size Command: Byte 1 Byte2 Byte3 ‘R’ (0x52) ‘U’ (0x55) <CR> (0x0D) Response: By

i TRADEMARK VEEMUX is a registered trademark of Network Technologies Inc in the U.S. and other countries. COPYR

NTI VEEMUX VIDEO MATRIX SWITCH 16 SS_01- Enable Auto Status Mode Command: Byte 1 Byte 2 Byte 3 Byte 4 Byte 5 Byte 6 ‘S’ (0x53) ‘S’ (0x53) Space

NTI VEEMUX VIDEO MATRIX SWITCH 17SX- Examine connections Command: Byte 1 Byte 2 Byte 3 ‘S’ (0x53) ‘X’ (0x58) <CR> (0x0D) Response: Multiple

NTI VEEMUX VIDEO MATRIX SWITCH 18 WEB INTERFACE A user may control the connections of the VEEMUX using a Web Interface via any web browser (see page

NTI VEEMUX VIDEO MATRIX SWITCH 19 Main Menu The VEEMUX main menu provides control over all functions of the switch. The administrative menu inclu

NTI VEEMUX VIDEO MATRIX SWITCH 20 For the Administrator Only: To save a configuraton, from the Stored Configurations user interface, use the drop-d

NTI VEEMUX VIDEO MATRIX SWITCH 21 Setup Pages These settings enable the user to configure the VEEMUX web interface connection. This change will ta

NTI VEEMUX VIDEO MATRIX SWITCH 22 User Management The Administrator can assign usernames and passwords to up to 14 users. Once assigned, the Admini

NTI VEEMUX VIDEO MATRIX SWITCH 23 Edit User To Edit a User, select “EDIT USER” from the USER MANAGEMENT section of the menu.

NTI VEEMUX VIDEO MATRIX SWITCH 24 Output Names From the Administration menu, the Output Names page can be displayed. This page enables the Admin

NTI VEEMUX VIDEO MATRIX SWITCH 25 To enable the scanning sequence for the output shown, place a checkmark in the “Sequence Enable” block. Tip: To

ii TABLE OF CONTENTS Introduction...

NTI VEEMUX VIDEO MATRIX SWITCH 26 Update Firmware

NTI VEEMUX VIDEO MATRIX SWITCH 27 Change Password Page

NTI VEEMUX VIDEO MATRIX SWITCH 28 Logout Page

NTI VEEMUX VIDEO MATRIX SWITCH 29 DEVICE DISCOVERY TOOL In order to easily locate the VEEMUX on a network, or to change network settings, the NTI De

NTI VEEMUX VIDEO MATRIX SWITCH 3012345 678 90OUT INSYSLo BattNTIRNetwork Technologies IncIRT-64X32SW INFRARED CONTROL (Optional) The IRT-64X32 (or

NTI VEEMUX VIDEO MATRIX SWITCH 31 How To Use The IRT The IRT-64X32 enables the user to control the connections of up to 32 input ports and 16 output

NTI VEEMUX VIDEO MATRIX SWITCH 32 Change Output Port Press the desired port number. If there is no change in the desired output port, the output

NTI VEEMUX VIDEO MATRIX SWITCH 33 Set Configuration The IRT-64x32 factory default setting is 32 inputs and 16 outputs. When the batteries are chan

NTI VEEMUX VIDEO MATRIX SWITCH 34 Battery Replacement The IRT has a low-battery indicator to let the user know when it is time to change the batte

NTI VEEMUX VIDEO MATRIX SWITCH 35 RS232 UPGRADE OF THE FRONT PANEL LCD FIRMWARE The firmware in the front panel LCD can be upgraded to include the l

iii Update Firmware...

NTI VEEMUX VIDEO MATRIX SWITCH 36 5. Press <L> to load the firmware (hex) file. This will prepare the file for transfer to the VEEMUX. If

NTI VEEMUX VIDEO MATRIX SWITCH 37 RS232 CONNECTION CABLES Pinout of RS232 port on VEEMUX The VEEMUX RS232 serial port is a DB-9F (female) connector

NTI VEEMUX VIDEO MATRIX SWITCH 38 Pinout for Matrix Y-1 Cable Arrows indicate signal direction. RACK MOUNTING INSTRUCTIONS T

NTI VEEMUX VIDEO MATRIX SWITCH 39 SPECIFICATIONS General Information DESCRIPTION SPECIFICATION Operating temperature -18°C - 55°C (0°F - 131°F)

NTI VEEMUX VIDEO MATRIX SWITCH 40 SAFETY STATEMENTS Grounding These products have protective earth ground terminals and are built with full atten

NTI VEEMUX VIDEO MATRIX SWITCH 1 INTRODUCTION The SM-nXm-15V-LCD (n = number of inputs (video sources), m = number of outputs (monitors)) video matri

NTI VEEMUX VIDEO MATRIX SWITCH 2 Materials Materials Supplied with this kit: • NTI SM-nXm-15V-LCD Video Matrix switch • IEC Line cord, country

NTI VEEMUX VIDEO MATRIX SWITCH 3 FEATURES AND FUNCTIONS 1. LCD Display- for visual indication of connection between the

NTI VEEMUX VIDEO MATRIX SWITCH 4 INSTALLATION Connect the Sources and Monitors 1. Power OFF all video sources (inputs) that will be connected t

NTI VEEMUX VIDEO MATRIX SWITCH 5 Connect RS232 RS232 control can be achieved using a separate user terminal or CPU with a terminal program. To ma